|
Post by subbiedoo on Apr 1, 2006 7:13:35 GMT 8
ok ... hindi ito 100% parin ... pero para sa akin, 98% effective ito unless merong mas-mahusay na "MacGyver" keysa sa akin :lol: ... anyways ... kailangan ma-block ang isang side ng mag (red triangle sa ilalim) para hindi pumasok and mag-bara ang BBs sa maling side ng "loader" para makaikot ito and mag-load ng BBs pwede nyo ilagay ang rampa sa side na iyon, or kung gusto nyo, lagyan nyo ng turnilyo ang "takip" ng mag ... basta kailangan ma "divert" lang ang BBs sa tamang side ng "loader" so kahit anong material ang gamitin nnyo, kayo na ang bahala ... PS: kailangan make sure nyo na hindi tatama ang galamay ng loading drum sa mod nyo or else hindi rin ito iikot hahahah and kung mag lalagay kayo ng turnilyo katulad ng akin, wag masyadong mahaba or hindi sasara ang takip ng mag nyo PPS: merong nag-advise sa akin sa Arnies Forums na hindi na raw kailangan ang blocker / rampa ... spray lang daw ang loob ng mag ng silicon oil ... pero sa tiningin ko, mali iyon kasi ... 1) mababasa ng silicon ang BBs ... then mababasa ang hop-up dahil sa BBs ... kung mabasa ang hop-up mo, hindi na accurate ang baril mo 2) mahal ang silicon oil (gamitin ko na lang sa GBBs ko) 3) hindi permanent ang silicon oil, paano ka na kung makalimutan mo mag lagay ng oil or kung maubusan ka ng suply??
|
|
|
Post by sargeniwde on Apr 1, 2006 8:12:53 GMT 8
Sir Subbiedoo, Thanks for posting this here...I was able to buy a second hand P90RD...and the hi cap that went with it was defective. The defect is that one of its gears shaft was lost. I just noticed now in your modified magazine that the gear (next to the loader) has a screw as a shaft. Eto po yung shaft na nawala sa magazine ko...tagos po ba sa cover yan?
Also, I bought a new magazine and I encountered the same damage. It appears that when the bb's inside the magz are not fully used and when we empty it, the wound spring would unwind and make the gear turn fast, thus causing the shaft to fly out of place. Buti na lang po, nakuha ko pa yung shaft. I plan to stick this permanently again using super glue.
Sarge
|
|
|
Post by SANDMAN on Apr 1, 2006 10:40:02 GMT 8
Thanks sir Subbiedoo for posting your pics and mag modification guide. I've tried several sizes of "harang" on the P90 mags and the one you posted(in red) is still the best size. Welcome to our forum sir....
@sargeniwde-I also encountered the same "flying shaft" problem with one of my mags. I simply replaced it with a like-sized screw and GLUED it in place for good measure. I also glued the shafts of my other mags so that they won't fly off anymore. The screw doesn't go all the way through... it's just the right lenght for the "socket".
For the SPRING UNWINDING problem, check if your mags still have the metal COUNTERWEIGHT installed- it's the half-moon metal thing connected to the gears. This will SLOW DOWN the unwinding just enough for the other BBS to "fall" into the gear teeth for loading. However, if the BBS are already JAMMED in the mag... the UNWINDING will still happen coz the BBS can't "fall" into the gear teeth.
I sometimes load my mags to 80% capacity only to minimize(if not totaly eliminate) the UNWIDING problem. But when I'm feeling lucky- I load up to 100% capacity and sometimes i can go through the entire game day without an unwinding problem. After loading the BBs in the mag, I usualy SHAKE them down(while holding the magazine follower) in order to get them to "stack" properly.
|
|
|
Post by sargeniwde on Apr 1, 2006 13:55:18 GMT 8
Sir Stan, Thanks for the advise...ayos na ayos. Galing talaga ng forum natin. I'll take pictures also for the others to see. Sarge
|
|
|
Post by sargeniwde on Apr 2, 2006 23:33:16 GMT 8
Sirs, I just also want to share my piece on the P90 Mag. As mentioned earlier in this thread, I the Hi-Cap that went with my RD was defective. The defect was that it didn't have anymore a plastic shaft for one of the gears. Please picture below.... So the next task that I had was to find a material that I can make a shaft from. I found some rivet nails lying around my tool box so I got one that is almost of the same diameter size. The materials needed are just the following: Cutter, Tweezers, pliers, and a file. Please see the picture below: The next picture would show how the rivet nail was modified and made as close as the original plastic shaft for the gear. Then the finished product vs the original component: And the finished good mounted on the gear/mag: Be sure that you put adhesive so that the shaft would not easily fly out again. This may not be the best solution in replacing the shaft but it is one option. So for those of you who lost a gear shaft in your mags, don't fret, we have an option to have it repaired. I hope you find this helpful. Happy and safe shooting to all. Sarge
|
|
|
Post by pvtpyle on Oct 6, 2006 20:11:17 GMT 8
Good evening mga sirs (P90 masters)!
just want to share my simple P90 hicap modification, I've also experienced flying shaft before during a game while trying to tap the mag due to misfeed. only to realized that the gear has broke free due to flying shaft.
what i've done is I opened my old Tamiya toolbox and looked for these small-thin screws used in fastening bumper bearings/rollers (front/end bumpers) with its self locking nuts (inner thread is teflon lined). removed the plastic plate holding all the magazine gears and mechanisms, bore a small hole just right in line with the gear (with the missing shaft op kors), fasten the gear with the screw and locked it with the teflon lined nut on the other side of the plastic plate. might as well use small washers on both ends of the small screw encasing the gear. the reason for using these self locking nut is for you to finely adjust the locking, para may laro ng konti yung gear sa loob. then put a small amount of mighty bond sa dulo ng screw if you want to ensure na di makakalas yung nut (im sure hindi talaga, maski di mo lagyan - just to give benefit of the doubt).
the only cons is, you cannot consume all the bbs since the "head" of the screw will prevent the magazine bb pusher to push all the bbs up to the last gear (with 7 teeth) driving the bbs to the mag hole. but what is 20-30 bbs left compared to accidental flying shaft. i havent experienced flying shaft again, even if you tap your mag. btw, after the mods, di ko na rin tina-tap ang mag ko due to misfeed. i dont know why, pero nakaka-7 hicap na yata ako na walang misfeed (test fire in auto and semi).
pvtpyle
|
|
|
Post by BRO SARGE on Oct 8, 2006 5:38:35 GMT 8
Sir pvtpyle,
Thanks indeed for your info. Also sir, if you can attach pics, that will really be nice.
As for not being able to finish 20 to 30 bbs...sir have you considered filing the bb pusher's lower portion so as to give it clearance for the screw head? Baka pwede nyo lang itodo...I remeber doing this with one of my mags.
BroSarge
|
|
|
Post by pvtpyle on Oct 9, 2006 11:33:10 GMT 8
Sir BRO SARGE,
That's brilliant sir! di ko naisip yun ah.. OKs nga yun, parang may canal yung bb pusher para mag-pass thru sa head nung screw. Thanks for the tips sir bro sarge.
pyle
|
|
|
Post by SANDMAN on Oct 10, 2006 9:02:35 GMT 8
P90 users have to inovate a lot to get the maximum performance from our AEGs.. though bro Sarge doesn't have to inovate much these days kasi may box mag na siya..
Post naman pics ng bagong gizmo mo bro sarge...
|
|
|
Post by BRO SARGE on Oct 11, 2006 9:58:46 GMT 8
Hello Stan,
Kayo naman sir...I still use the TM Hi-Cap mags...I still have 4 of them...am selling the 2 though...hehe.
As for your request, I just posted a lot of my RD and TR's pics there...please see the Pictures forum...pati set up na natutunan ko sa inyo nilagay ko na doon...para isang upload na lang...
Thanks, BroSarge
|
|
|
Post by Daryl P90 User on Dec 27, 2006 22:17:52 GMT 8
I have a question. How about reducing the amount of teeth in the hi-cap to allow more BBs to go inside? If you wind the magazine there are chances that 2 or less BBs go inside right? Make the magazine have around four or less teeth instead of seven. Just wondering if it would work with the blocker mod.
|
|
|
Post by BRO SARGE on Dec 31, 2006 20:04:12 GMT 8
hello sir daryl...welcome po sa forum...well...your suggestion is logical...kaso I had a friend who broke one of loader's teeth...ala rin pong effect. there would also be a point that the bb's will jam
|
|
|
Post by Daryl P90 User on Jan 9, 2007 21:19:05 GMT 8
|
|
|
Post by slegge on Aug 6, 2008 21:19:58 GMT 8
Hey I was wondering if anyone could translate the first post to english? I've been crawling trough a lot of forums looking for P90 mag fixes but this seems to be the only one thats still up
|
|
|
Post by BRO SARGE on Aug 11, 2008 13:58:57 GMT 8
Hello Sledge, where are you based?
|
|