LT. diablo
Moderator-1
High SPEED, Low DRAG.....
Posts: 464
|
Post by LT. diablo on Sept 18, 2006 6:15:52 GMT 8
Ako sir jojo.. pa rewind ko sa ako eg1k.. kung di lang ka busy ha? hehehe
|
|
|
Post by 9th on Sept 18, 2006 10:03:55 GMT 8
anytime but don't give me a timetable mga brother!
<<jojo>>
|
|
|
Post by 9th on Sept 18, 2006 16:09:34 GMT 8
browsing this thread...i found something interesting...hmmnn! image from wgc.com from ics turbo 3k notice the different? the point where to start the advance commutator... <<jojo>>
|
|
|
Post by 9th on Sept 18, 2006 16:11:22 GMT 8
nasa ilalim ang sa wgc...nasa ibabaw ang ics...
<<jojo>>
|
|
|
Post by 9th on Sept 18, 2006 16:13:15 GMT 8
mag matter ba eto?
<<jojo>>
|
|
|
Post by SANDMAN on Sept 19, 2006 8:11:22 GMT 8
I'm afraid that it's waaay over my head sir Jo... try daw pangutana didto sa RC forums...
|
|
|
Post by 9th on Sept 19, 2006 10:41:50 GMT 8
yup! i may post mmya sir stan
<<jojo>>
|
|
|
Post by Han_Solo on Jul 15, 2007 11:49:49 GMT 8
browsing this thread...i found something interesting...hmmnn! image from wgc.com from ics turbo 3k notice the different? the point where to start the advance commutator... <<jojo>> Sir Jo, For reference yung pic. Yung before sa arrow, yung kung asan naga contact ang carbon brush.. di ko alam ang name, pansin ko kase sunog na sa Turbo3k ko. May tuklap na ang bronze & exposed na konti black & my motor is dead. Ito kaya ang culprit? Duda ko kase na kahit i-rewind di mag ubra kay lain man ang daut. I have a Stock CA motor with a considerably weaker magnet compared to T3K, pwede kaya I-swap yung buong shaft, ipailt dun sa sunog na T3K shaft? Help in any way would be appreciated..
|
|
|
Post by 9th on Jul 15, 2007 13:28:17 GMT 8
commutator ang tawag sir...napodpod eto usually kay mejo gahi ang carbon brush....or nag stock up eto then nag produce ng spark kaya masunog ang commutator...
tanggala sir ang commutator sa CA then replaced mo sa T3k. :-)
|
|
|
Post by Han_Solo on Jul 15, 2007 14:01:06 GMT 8
Sige try nako sir.
Pero unsaon pag tanggal sa pinion gear nga force fit, pwede ba dukdukon?
|
|
|
Post by Han_Solo on Jul 15, 2007 14:34:13 GMT 8
di madala ug dukduk...ugma na jud ni para pinion remover.
Salamat sir Jo.
|
|
|
Post by 9th on Jul 15, 2007 14:46:33 GMT 8
Sige try nako sir. Pero unsaon pag tanggal sa pinion gear nga force fit, pwede ba dukdukon? ayaw dukduka sir kay mataktak ang magnet ;D
|
|
|
Post by an2nymous on Jul 20, 2007 2:02:58 GMT 8
kung ang carbon brush ang mahilis unsa pwede remedy ani?naa ba mapalit carbon brush sa eg1000?
|
|
|
Post by 9th on Jul 20, 2007 2:25:01 GMT 8
use the junk r6 sir...murag naa ko nakit an sa tindahan sa ersop sir...
|
|
|
Post by SANDMAN on Jul 30, 2007 17:58:13 GMT 8
Marunong ka pala mag-repair ng motor sir Jo?
|
|