Jay2
Kabo
Give us the tools and we will finish the job
Posts: 116
|
Post by Jay2 on Jan 13, 2007 12:05:28 GMT 8
mga sir help naman, misfeeds always irked me. what seems to be the problem? wat po dapat gawin. my gun is a CA m15a4. internal specs: sp 140 spring CA STU helical gears Guarder air seal nozzle Gurder polycarbonate piston body CA boreup kit systema tight barrel which of these specs caused the misfeeds? sbi nila ung nozzle daw. another version ay yung tappet daw.  |
|
|
|
Post by vernes on Jan 13, 2007 13:03:07 GMT 8
try nyo sector gear chip sir..hehe
|
|
|
|
Post by ZeeZeeTop on Jan 13, 2007 14:06:14 GMT 8
mga sir help naman, misfeeds always irked me. what seems to be the problem? wat po dapat gawin. my gun is a CA m15a4. internal specs: sp 140 spring CA STU helical gears Guarder air seal nozzle Gurder polycarbonate piston body CA boreup kit systema tight barrel which of these specs caused the misfeeds? sbi nila ung nozzle daw. another version ay yung tappet daw. hmmm.... bakit mo pinalitan ng airseal nozzle? yung CA na boreup kit meron na iyo nozzle kasama eh. try mo balik yung nozzle na kasama sa kit or compare mo yung length nung dalawa. meron kasi instances na maikli yung nozzle ng CA compared sa Guarder eh... check mo rin using other magazines sir, sakit kasi talaga ng CA mags ang misfeeds... :  : this AEG would surely post a 500++ fps... pero sa tournament nila 450 lang ha....  |
|
|
|
Post by ROSCOE on Jan 13, 2007 15:23:53 GMT 8
o nga, air sealed na ang nozzle kasama ng bore up. daming factors ang misfeed, as what sir jade had said baka nga nozzle length or sa magazines mo. pwede rin dahil sa placement ng hop system baka sobrang layo sa geabox or sobrang lapit. ok din remedy ang sector chip but it doesnt necessarily cure misfeeds. : : ganda ng setup mo sir. |
|
|
|
Post by denski on Jan 13, 2007 16:18:57 GMT 8
Misfeeds... either of the following:
1. Your mag has feeding problems
2. Tappet plate doesnt faciliate proper bb follow thru
3. Inner barrel has bumps and bents on the inside
4. Cylinder air capacity cannot handle very long and tight barrels installed
5. Low battery/low ROF
6. Bad bbs used
7. Piston, cylinder, motor need proper adjustment
8. Hop assembly has a leak/tear/crack
9. Inner barrel is not installed properly
10. Excess lube in the inner barrel
11. Dirty mag, nozzle, inner barrel
12. Dry hop up rubber
13. Moving/unstable gearbox
14. Cylinder air leak
15. Unstable front assembly (for m4)
16. Improper crowning of inner barrel
...just some of the things I can think about.
|
|
Jay2
Kabo
Give us the tools and we will finish the job
Posts: 116
|
Post by Jay2 on Jan 15, 2007 13:28:20 GMT 8
mga sir tnx po sa mga information. very informative po. return the CA nozzle already. i also had my mag repaired. mahal ang bagong mag eh. misfeeding is hardly noticeable now. Ask lang, when can you know if defective na ang tappet plate? Sir Denski has posted a while ago that tappet plate can indeed cause misfeeds. tnx mga sir...  |
|
|
|
Post by PATHFINDER on Jan 22, 2007 21:03:17 GMT 8
sir jay mhirap po ipaliwanag ung problema nyo but about wat sir denski is talking about maraming factors ang misfids problem hes right, kung sakali misfid pa rin,just pm me or txt me ask mo number ko ke sir alakdan id be glad to make way to your prob anytime sir
|
|
Jay2
Kabo
Give us the tools and we will finish the job
Posts: 116
|
Post by Jay2 on Jan 23, 2007 18:45:57 GMT 8
@ sir pathfinder: thanks sir... this problem has been bugging me already. wheew syang ang lakas ng bengbeng pag ngamisfeed pa rin...  |
|
|
|
Post by Oakley ( Ka Ryan ) on Jan 24, 2007 10:23:27 GMT 8
Mga Sirs share ko lang experienced ko , I have m15a4 cqb compact 3 month ago during that time fresh from the box ginamit ko agad taka ako nagamisfeed cya even bago pa. hinayaan ko and adjust ko hop up to think na un ang probs pero ganon pa rin. Binuksan ko ang unit and i've discovered na ung tappet plate pala nya masikip sa gear box. So ang ginawa ko sand ko lng ng kaunti para magkaroon ng play. after nun wala na misfeed nya. Add ko pa sector chip kalas na kaau hinuon ug bb's. Try also to lube ur inner barrel at hop up kasi one reason din un sa misfeeding.  Share lang po.... |
|
Jay2
Kabo
Give us the tools and we will finish the job
Posts: 116
|
Post by Jay2 on Jan 24, 2007 11:50:20 GMT 8
tnx sir oakley... ;D maybe by this saturday ipapacheck ko siya. hehe, parang tao. baka nga yung tappet plate kasi stock pa yun eh. have already chnge the barrel and the hop-up rubber. bago pa yun na lubricate pero may misfeeds pa rin.
|
|
|
|
Post by Oakley ( Ka Ryan ) on Jan 26, 2007 6:30:33 GMT 8
Sir balitaan mo agad ako after kung ano talaga probs ng unit mo. thanks sir. ;D
|
|
Jay2
Kabo
Give us the tools and we will finish the job
Posts: 116
|
Post by Jay2 on Jan 29, 2007 12:04:20 GMT 8
sir, ala ko pa napacheck... i think may problem na yung CA magazine ko because when i try with other mags, there seem to be a reduction in the misfeeds. i'm not so sure though. siguro mas may problem nga yung mag kaysa sa internal. |
|
|
|
Post by Oakley ( Ka Ryan ) on Jan 29, 2007 14:36:01 GMT 8
Ah okey sir. mas mainanm na rin un sir at hindi ang internals mo talaga ang may major probs. Try to check sa Covert Ops may DBoy sila na brand ng mags 190 rounders cya ala probs daw sa misfeeding. It will cost you 600 to 700 pesos. May setbacks din kasi ung CA na mag sir kahit bago pa, hinihilot ko na lang minsan para mawala.  |
|
3pdf
Tenyente
Jump, run, make noise but do not sin!
Posts: 5
|
Post by 3pdf on Jan 29, 2007 23:38:03 GMT 8
try mo sir src mags tnx. |
|
Jay2
Kabo
Give us the tools and we will finish the job
Posts: 116
|
Post by Jay2 on Jan 30, 2007 14:45:42 GMT 8
maganda nga daw yung src mags sir pero siguro i'm gonna save on a marui mag. tested na daw na mag yun eh. pero papacheck ko pa rin yun internals para sigurado. ;D |
|
